Water System and Pumps

An automatic float switch that turns your bilge pump into a fully automatic dewatering system. As the water level rises, this compact float (113x54 mm) triggers your pump on, and when the water recedes, it turns the pump off. An essential device to protect your boat from flooding when no one is on board.

• Automatic pump control: Activates and deactivates your bilge pump based on water level, no manual switching needed.
• Compact design: Small form factor (~113 mm length) allows easy installation even in tight bilge areas.
• Durable housing: Impact-resistant, non-corrosive plastic construction built for the marine environment.
• Universal compatibility: Works with most 12V/24V bilge pumps (supports loads up to ~15A) – a standard solution for small and mid-sized boats.

Protect your boat from unwanted siphoning or backflow with this anti-siphon valve (vented loop) for marine toilets. Installed high above the waterline, this valve breaks the vacuum in the toilet hoses, preventing continuous water flow and potential flooding.

• Anti-Siphon Protection: Breaks siphon effect by allowing air into the system when needed, so water cannot flow uncontrollably.
• Multiple Sizes: Available in Ø19 mm, Ø25 mm, and Ø38 mm internal diameters to fit the most common intake and discharge hose sizes.
• Durable Construction: Made of high-quality plastic (white) resistant to seawater, UV rays, and chemicals for long service life.
• Easy Installation: Standard design with mounting holes for quick installation on a wall or bulkhead; should be mounted at the highest point above the waterline.
• Onboard Safety: A must-have for toilets installed below the waterline – prevents backflow that could flood your boat or cause interior damage.

Premium AISI 316 stainless steel thru-hull fittings featuring an integrated hose barb (tailpiece) for direct hose connection. Available in common hose sizes 3/8", 1/2", 3/4", and 1", these thru-hulls allow you to run a hose straight to the fitting without needing a separate adapter. Each fitting has a wide flange for the hull exterior and a barb on the interior side to securely clamp your hose. They are ideal for above-waterline drains (scuppers, sink drains, livewell overflow) or any application where a hose needs to pass through a bulkhead or hull with a secure, leak-free connection. Manufactured from marine-grade 316 stainless, they offer superior strength and corrosion resistance compared to plastic fittings.

• Material: AISI 316 stainless steel, one-piece body with barb – rustproof and strong
• Hose Sizes: Comes in 3/8", 1/2", 3/4", 1" barb diameters to fit standard hoses
• Design: Mushroom head outer flange and ribbed hose tail interior for hose clamping
• Application: Direct hose connections for bilge pump discharge, sink or shower drains, livewell/baitwell connections, fuel tank vents (check size), etc.

The Keji II deck shower from the Elissa series features an advanced shower head with “Continuum Flow” technology for a steady, strong stream. With a 118x97 mm stainless housing and no mixer (for cold or pre-mixed water from your system), this model combines compact size with an enhanced shower experience – an excellent choice for discerning boat owners.

• AISI 316 stainless steel housing (118×97 mm) with polished finish, UV and corrosion resistant
• Large Keji II shower head (chromed plastic) with Continuum Flow for continuous, high-volume spray
• Compact form, fits in tight spaces (mounting cutout ~90×70 mm)
• 2.5 m white nylon hose for high flexibility (options: 4 m or reinforced hose available)
• No mixer – connects to a single water line; easy upgrade to existing shower setups

Automatic float switch for 12V bilge pumps (supports up to 10A load), featuring a protective cover. Reliably triggers your pump when water rises and stops it when water recedes, while the cover shields the mechanism from debris for trouble-free operation.

• For 12V systems: Designed for 12V pumps (up to 10A) – ideal for small to mid-sized boats.
• Automatic operation: Float monitors water level and turns pump on/off with no manual intervention.
• Protective housing: Cover shields the float mechanism from debris, preventing jams or damage.
• Easy installation: Standard design with mounting holes – quick to install and wire in-line with your pump.

Restore the stability and reliability of your manual marine toilet with this replacement base. It provides a solid platform for mounting the bowl and pump, eliminating leaks and wobbling caused by a cracked or damaged base.

• Sturdy Support: Made of high-strength plastic that withstands the stresses of toilet use in marine conditions.
• Watertight Sealing: Ensures a tight fit with the toilet bowl and pump, preventing any leakage at the base.
• Standard Fit: Exact replacement for common manual toilet models (e.g., the 01430 series), with pre-drilled holes to match the original deck mounting pattern.
• Corrosion-Resistant: Material resists saltwater and cleaning chemicals for long-lasting use without cracking or warping.
• Easy Replacement: Allows quick restoration of your toilet – simply remove the old base and bolt the new one in place using the existing hardware.

The Elegant wall-mount shower box with Mizar push-button head is the perfect solution for vertical installation on board. The compact white enclosure (98.5x106 mm) houses a chromed brass push-button shower head that releases water on demand. Its UV-resistant housing and shallow depth (~45 mm) make it ideal for cockpit walls and transoms.

• Vertical bulkhead or transom mounting (outer size 98.5×106 mm)
• White ASA plastic housing, UV-stable and impact-resistant
• Chromed brass Mizar shower head with push-button – on-demand flow and water saving
• 2.5 m reinforced PVC hose stored inside; 4 m option available for larger vessels
• Shallow installation depth (~45 mm) – great for thin panels and aftermarket upgrades

Universal automatic float switch for bilge pumps, compatible with 12V, 24V, and 32V systems (supports up to 14A). This heavy-duty float enables automatic control of higher-power pumps, ensuring reliable operation even on larger boats and yachts.

• Multi-voltage: Operates on 12V, 24V, or 32V – a flexible choice for various vessels.
• High amperage: Handles up to 14A current – suitable for higher-capacity pumps with strong output.
• Rugged build: Heavy-duty design with water-resistant housing and a reliable mechanism for long service life.
• Auto protection: Activates your pump as water rises and shuts it off as it recedes – prevents flooding without human intervention.

Upgrade onboard comfort with this luxury marine toilet bowl, complete with seat and lid. The “luxury” model offers a larger, more comfortable design and premium materials, providing a home-like feel and lasting durability at sea.

• Enhanced Comfort: A larger, ergonomic bowl that offers comfort comparable to a home toilet.
• Quality Seat: Sturdy high-grade plastic seat and lid with reinforced stainless steel hinges for stability and long life.
• Easy Cleaning: Smooth porcelain surface resists stains and odors, making it easy to clean and not harbor bacteria.
• Standard Compatibility: Fits the bases and pumps of most marine toilets (e.g., replaces standard model 01431-3) – a quick upgrade to a higher class without complicated modifications.
• Durability: Designed for marine use, this luxury bowl withstands vibrations, sudden movements, and temperature changes, maintaining its appearance and function for years.