EVAL

Robust cover for jet skis, made from waterproof 300D polyester with PA/PU coating. Provides superior protection for your personal watercraft from sun, rain, dust, and debris, especially during storage out of water or off-season. Available in 3 sizes to fit different jet ski types:

• 300D heavy fabric – tear-resistant polyester with double-stitched seams, withstands UV rays and heavy rain; inner PA coating for complete waterproofing.
• Full coverage – covers the entire jet ski (hull, seat, handlebars), shielding it from fading, scratches, and dirt during storage or transport.
• Elastic hem – integrated elastic around the bottom edge for a snug fit to the hull; additional tie-down straps keep the cover secure in wind or when trailering.
• 3 sizes available – S for small jet skis (~260-290 cm length), M for standard 2-3 seater models (~270-320 cm), L for large 3-seater and touring models (~300-340 cm length, extra width).
• Easy to use – lightweight yet tough cover stretches over your jet ski in a minute; when removed, it folds neatly into the included storage bag.

A right-angle mounting plate for installing a gas spring (gas strut) at 90°, made of premium AISI 316 stainless steel. This bracket provides a sturdy anchor point for one end of a gas lift on boat hatches, lockers, and doors. It comes in two versions to accommodate different gas spring sizes/types. Key features:

• 90° Design: Allows a gas spring to be mounted at a perpendicular angle between a lid and frame – ideal for horizontal hatches, cockpit lockers, cabinet doors, etc.
• Stainless Steel 316: Strong, corrosion-proof construction suitable for marine use (won’t rust in damp, salty conditions)
• Compact Size: Bracket plate measuring ~30x50x30 mm that fits into tight spaces without adding bulk; pre-drilled holes for easy bolt or screw installation
• 2 Variants: Different versions available to fit smaller vs. larger gas springs (e.g., different ball stud sizes) – choose according to your gas strut’s specifications

A replaceable large oar blade for Ø35 mm diameter shafts, intended for heavy-duty oars on larger boats. The 60 x 12.5 cm size provides greater paddling force for moving the boat quickly. Made of reinforced ABS plastic, this spare blade withstands intensive rowing and harsh conditions. Available in different colors (e.g., grey, black) to match your equipment.

• Ø35 mm Compatibility: Fits handles with 35 mm diameter – typical for oars of larger inflatables and lifeboats.
• Large Surface: The 60 x 12.5 cm dimensions allow for a stronger push with each stroke, ideal for heavy boats or against currents.
• Reinforced Plastic: Constructed from high-strength ABS, reinforced to resist bending and cracking; withstands UV rays and saltwater without degradation.
• Easy Installation: Quick to swap – slide the new blade onto a Ø35 mm shaft and secure it firmly with a bolt/pin.
• Color Variety: Offered in more than one color option (e.g., black or grey) so you can replace your blade with a close match or improved visibility.

Round watertight flush deck plate equipped with a durable inner storage bag to keep items dry. This “hatch + bag” combo transforms a standard inspection port into a useful storage compartment, protecting your gear from water and dirt. Key features:

• Extra Dry Storage: Provides a waterproof space to stash valuables, tools, phones, documents, etc., safely inside your boat’s hull or console
• Sturdy Bag: Flexible inner bag (~280 mm deep) made of tough waterproof fabric that attaches to the hatch; easy to remove for access and cleaning
• Universal Hatch: Round hatch with an outer flange diameter of approx 240–250 mm and a cutout Ø205 mm, made of high-quality UV-resistant plastic (white color), featuring a rubber O-ring for a reliable watertight seal
• Easy Installation: Designed for flush mounting in deck, cockpit, or any flat surface – requires a Ø205 mm circular cutout; secures with screws through the flange holes and proper sealing to ensure full water tightness

A robust rail guide with a swiveling roller, designed to guide ropes or loads being pulled at an angle. This compact (18 cm) metal assembly withstands working loads up to 200 kg and is perfect for mounting on trailers or decks where the pull line is off-center. The pivoting roller automatically aligns with the direction of force, ensuring smooth boat loading onto a trailer or hauling heavy gear without binding or chafing.

• Short track (18 cm) with a movable carriage – allows ~10–15° off-axis pulling without snagging or jamming the rope
• Swivel-mounted steel roller – follows the pull direction, providing smooth feed and reduced friction for loads up to 200 kg
• Heavy-duty metal construction (stainless steel) – impact and corrosion resistant, suitable for use in wet/salty environments and demanding conditions
• Built-in locking handle (spring pin) – secures the sliding carriage when needed and enables easy release for adjustment or removal
• Recommended uses: boat trailers, ramps, and davits – ideal for safely guiding a boat onto a trailer when it’s slightly off-line, as well as redirecting tensioned lines on deck without strain

Rectangular opening boat window (portlight) measuring 33×19 cm, built with high-quality marine-grade materials. This portlight combines a sturdy anodized aluminum frame with a thick 10 mm plexiglass pane, providing light, ventilation, and watertight performance on board. Key features:

• Aluminum Frame: Strong anodized aluminum frame resists corrosion – will not warp or rust even with long-term saltwater exposure
• Thick Lens: Window made of 10 mm plexiglass (acrylic) – impact-resistant and UV-resistant; the thick construction ensures strength and safety against waves and knocks
• Opening Design: Fitted with hinges and locking handles, allows easy opening for cabin airflow; secure locking mechanism that compresses a rubber seal to keep water out when closed
• Universal Size: Approx. 33×19 cm dimensions make it suitable for many small and mid-sized boats – ideal for cabin sides, heads (bathrooms), or as an extra side window on a sailing yacht or cruiser

The plastic strap bridge is a strong, durable loop designed for securing webbing straps to boat covers and canopies. Made of UV-resistant nylon, it won’t corrode and withstands marine conditions. It comes in two sizes to fit different strap widths, providing a secure anchor point for cover tie-downs during transport or storage.

• Material: High-strength plastic (nylon) construction, UV-stable and saltwater-proof
• Sizes: Small bridge (27 mm inner width) fits straps up to ~25 mm; Large bridge (40 mm inner width) fits straps ~40 mm wide
• Installation: Easily mounts with screws or rivets to the boat hull, frame, or canvas as needed
• Use Cases: Ideal for boat canopies, bimini tops, covers, and cargo straps – keeps webbing tight and in place
• Advantages: Will not rust, lightweight with smooth edges (prevents strap chafe and wear)

High-quality Omega-shaped bow shackles made of 316 stainless steel, featuring a hex socket (Allen head) screw pin. These shackles provide secure connections for chains, ropes, and rigging, combining maximum corrosion resistance with enhanced locking security. Key features:

• AISI 316 Stainless Steel: Constructed entirely from marine-grade stainless – ideal for sail and power boats, resisting saltwater corrosion and constant moisture
• Hex Socket Pin: The locking pin has an internal hex drive (Allen key type) and an O-ring – this design prevents self-loosening under vibration and cannot be easily opened without the proper tool
• Bow Shape: Wide “omega” bow shackle allows attachment of multiple lines or chains and handles load from various angles better than D-shackles
• Sizes 6–13 mm: Available in sizes to suit any need – from 6 mm for small craft and accessories up to 13 mm for heavy-duty loads on large yachts. Each thickness roughly matches the chain or rope diameter (e.g., 8 mm shackle for 8 mm chain)

Stainless deck pad eye with lifting ring, designed for securing gear, ropes, or equipment on a boat. This four-bolt base provides an extremely strong attachment point that can handle high loads. Available in three sizes/thicknesses for different applications. Key features:

• AISI 316 Construction: Entire pad eye and ring are made from cast 316 stainless steel with polished finish – outstanding resistance to corrosion and marine conditions
• Movable Ring: Round ring that can lay flat or lift up – provides flexibility for clipping on carabiners, hooking ropes or straps, and lies down out of the way when not in use
• 4 Mounting Holes: Rectangular base with four pre-drilled holes (one at each corner) – distributes load evenly and ensures secure fastening to deck, transom, or structure
• Three Sizes: Plate/ring thickness approximately 5 mm, 6 mm, and 8 mm respectively. Greater thickness equals higher load capacity – choose the size according to the needed strength (light, medium, or heavy-duty tasks)

The EVAL console cover shields your boat’s helm (wheel, instruments, electronics) from rain, dust, and UV damage. Made of tough 300D polyester with a waterproof PU coating, it features reinforced double stitching and an integrated drawstring hem for a snug fit. Available in 4 different sizes to suit a range of boats – from compact RIBs to larger center-console vessels.

• Material: 300 Denier polyester fabric with waterproof PU coating; built to withstand sun and seawater
• Design: Elastic cord perimeter + drawstring fastening – cinches tight around the console for secure fit
• Seams: Double-stitched seams with extra reinforcement/taping to endure strong wind without tearing
• Protection: UV-resistant treatment prevents sun damage and fading; keeps console dry and dirt-free in all weather
• Sizes: 4 sizes (S, M, L, XL) – fitting most boats (approx. 3 m up to 7 m). Choose the right size based on your console’s height and width.